Trans 300.40(6)
(6) The complete exhaust system shall be tightly connected and free from leaks.
Trans 300.40(7)
(7) All emission control systems, components and parts shall be maintained in accordance with manufacturer's specifications.
Trans 300.40 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (1), (5), cr. (5m), (7), (8),
Register, February, 1995, No. 470, eff. 3-1-95; am. (1) and (5m),
Register, December, 1997, No. 504, eff. 1-1-98;
CR 15-069: am. (1), cr. (1m), am. (3)
Register April 2016 No. 724, eff. 5-1-15.
Trans 300.41(1)(1)
Each bus shall be equipped with a fire extinguisher mounted in full view in the driver's compartment or mounted inside a compartment in the driver's area if the compartment is in plain view and is labeled “Fire Extinguisher" in red letters to indicate its location.
Trans 300.41(2)
(2) The fire extinguisher may be locked or kept in a locked compartment provided it is not locked when passengers are being transported.
Trans 300.41(3)
(3) Any fire extinguisher purchased after July 1, 1977, or utilized on a bus that was manufactured after January 1, 1978, shall utilize dry powder or Halon 1211. The fire extinguisher shall be 10 BC rating or a combination of 2 extinguishers with a total of at least 10 BC rating. Any bus manufactured after January 1, 1984, shall use only a single extinguisher.
Trans 300.41(4)
(4) Each extinguisher shall be kept fully charged and sealed.
Trans 300.41 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (1), (3), r. (5),
Register, February, 1995, No. 470, eff. 3-1-95.
Trans 300.42(1)(1)
Each school bus shall carry a first aid kit. The container shall be moistureproof and dustproof and of rigid construction. The kit shall be mounted in full view in the driver's compartment, or it may be placed in an enclosed unlocked compartment in the driver's area providing the compartment is labeled “FIRST AID KIT" or marked with a red cross emblem in plain view indicating the location of the kit. The kit shall be removable without the use of any tools or keys.
Trans 300.42 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (2), r. (3), (4), renum. (5) to (3),
Register, February, 1995, No. 470, eff. 3-1-95.
Trans 300.43
Trans 300.43 Fenders. Each school bus shall provide protection from debris thrown by the tires by the use of fenders or body construction. The tire tread shall be within the fender or body construction.
Trans 300.43 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83.
Trans 300.44(1)(1)
The floor in the underseat, driver's compartment, step-well and the toeboard areas, including the tops of the wheel housings, shall be covered with a fire-resistant material.
Trans 300.44(2)
(2) Type A-II buses shall have the floor covering secured so it cannot shift. The edges and seams shall be secured. The covering shall be of a slip resistant material.
Trans 300.44(3)
(3) Type A-I, B, C or D school buses shall have floor covering on the total floor area. The aisle, step-well and entrance shall be of slip resistant rubber type material or equivalent material as certified by the manufacturer, when either wet or dry. The covering may not be cracked and shall be securely bonded or fastened to the floor. All seams shall be sealed.
Trans 300.44 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (1), (3),
Register, February, 1995, No. 470, eff. 3-1-95
; am. (2) and (3),
Register, December, 1997, No. 504, No. 1-1-98.
Trans 300.45(1)(1)
Alterations to the frame side members may only be made by the chassis or body manufacturer.
Trans 300.45(2)
(2) Holes are not permitted except where originally provided in the chassis frame. There may be no welding to the frame except by the chassis or body manufacturer.
Trans 300.45 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (2),
Register, December, 1997, No. 504, eff. 1-1-98.
Trans 300.46
Trans 300.46 Fuel tank and fuel system integrity. Trans 300.46(1)(1)
All fuel systems and tanks must be maintained free of leaks. The fuel tank shall be attached to the bus in a manner that prevents any movement of the tank while the bus is in motion.
Trans 300.46(2)
(2) All fuel lines shall be secured in a manner that will prevent wear.
Trans 300.46(3)
(3) The filler pipe or device shall be located so that the fuel, if spilled or overfilled, will not drip or drain on any part of the exhaust system.
Trans 300.46(4)
(4) Every fuel system shall be properly vented to prevent any accumulation of fumes.
Trans 300.46(5)
(5) The fuel systems and tanks shall meet FMVSS 301, fuel system integrity, and all other federal and state standards and regulations applicable for the type of fuel used at the time of manufacture.
Trans 300.46 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (5),
Register, February, 1995, No. 470, eff. 3-1-95.
Trans 300.47(1)(1)
An inside temperature of not less than 50
° fahrenheit at average minimum January temperatures as established by the U.S. department of commerce, weather bureau, for the area in which the bus is to be operated shall be maintained throughout the bus.
Trans 300.47(2)
(2) The heater hose shall be adequately supported to guard against excessive wear or abrasion and may not interfere with or restrict the operation of any engine function. Heater lines inside the passenger compartment shall be shielded to prevent accidental contact by the driver or passengers.
Trans 300.47 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (2),
Register, December, 1997, No. 504, eff. 1-1-98.
Trans 300.48
Trans 300.48 Horn. Every bus used to transport pupils shall be equipped with a horn in good working order and capable of emitting a sound audible under normal traffic from a distance of not less than 200 feet.
Trans 300.48 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83.
Trans 300.49(1)(1)
The inside height of the school bus shall be 72 inches or more, measured metal to metal, at any point on longitudinal center line from front vertical bow to rear vertical bow.
Trans 300.49(2)
(2) Type A-II school buses need not comply with this section.
Trans 300.49 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (2),
Register, December, 1997, No. 504, eff. 1-1-98.
Trans 300.50
Trans 300.50 Insulation. The ceilings and walls of buses manufactured in 2 stages and all type A-I, B, C and D buses shall be insulated to reduce heat and cold transfer.
Trans 300.50 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83
; am.
Register, December, 1997, No. 504, eff. 1-1-98.
Trans 300.51(1)(1)
Every school bus shall be equipped with the following illuminated instruments to indicate malfunctions or gauges to indicate a measure or capacity:
Trans 300.51(1)(a)
(a) Air pressure or vacuum, where air or vacuum brakes are used with low energy supply warning systems.
Trans 300.51(2)
(2) All instruments and gauges shall be in operating condition and shall be mounted so as to be clearly visible to the seated driver.
Trans 300.51 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (1) (a), (c), (d), (f),
Register, February, 1995, No. 470, eff. 3-1-95.
Trans 300.52(1)(1)
Every school bus shall have a fire resistant inner lining on the ceilings and walls. The interior rearward metal panels shall be lapped over forward panels to reduce the likelihood of injury in the event of separation. The exposed edges of all interior panels shall be beaded, hemmed or flanged.
Trans 300.52(2)
(2) Projections from the ceiling may not be allowed in the entrance way or aisle. Except for the driver's compartment, all speakers and accessory lighting devices shall be flush mounted or may extend up to one inch if edges are rounded or tapered. Accessory lighting shall be maintained in proper working condition.
Trans 300.52(3)
(3) A convex mirror may be mounted on the inside rear of the school bus.
Trans 300.52 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am. (2), cr. (3),
Register, February, 1995, No. 470, eff. 3-1-95
; am. (2),
Register, December, 1997, No. 504, eff. 1-1-98.
Trans 300.53
Trans 300.53 Ladders. A school bus may not have a ladder attached to the interior or exterior while it is in motion.
Trans 300.53 History
History: Cr.
Register, February, 1983, No. 326, eff. 3-1-83; am.
Register, December, 1997, No. 504, eff. 1-1-98.
Trans 300.54(1)(1)
The following lights, lamps, and reflectors are required on a school bus. Each lamp shall be operational and meet the applicable SAE specifications as provided in this section.
Trans 300.54(1)(a)
(a) A school bus painted in accordance with s.
347.44 (1), Stats., shall be equipped with alternating flashing lights which conform to the following requirements:
Trans 300.54(1)(a)1.
1. The bus shall be equipped with 2 red warning lamps at the rear of the bus and 2 red warning lamps at the front of the bus, which shall be controlled by a manually actuated switch and shall flash alternately at rate of 60 to 120 cycles per minute. A brake or door operated switch is not permitted. The “on" period shall be long enough to permit bulb filament to come to full brightness. Two additional red warning lamps to the front and 2 to the rear may be installed inboard and at the same level as the required lamps. If so equipped, the system of red warning lamps shall be of equal size and wired so that the inboard lamps are energized manually. The outboard lamps shall be automatically energized and the inboard lamps automatically de-energized when the stop signal arm is extended.
Trans 300.54(1)(a)1.a.
a. An option is permitted whereby 2 additional alternating flashing red lights may be mounted on both the front and rear of the bus. The additional front facing lights shall be located between the bottom of the windshield and the top of the highest headlamp. They may be mounted on the fender or the cowl.
Trans 300.54(1)(a)1.b.
b. The additional rear facing lights may be separate lamps mounted within 12 inches above or below the directional turn signals or may be incorporated in an existing lamp. Any incorporation with an existing unit may not interfere with or override the existing unit's function. If the optional lighting system utilizes the rear directional signals, it shall be so designed that if both the directional signal lamp and the flashing red lights are activated during the same period of time, the flashing warning signals shall revert to only the 2 required warning signals until such time as the directional signal lamp is deactivated. The optional system may not be incorporated with the stop signal lamp.
Trans 300.54(1)(a)1.c.
c. The optional system shall have units with a red lens of at least the same size as the required alternating lights. The alternating “on," “off" positions shall be opposite from those of the required alternating lights. The effect will produce the required top mounted flashing light and an optional mid–height mounted light to flash on opposite sides simultaneously. The result can be described as a “wig–wag" or “cross–arm" effect.
Trans 300.54(1)(a)1.d.
d. A school bus shall be equipped with warning signal lights mounted at the same level as high and widely spaced laterally as practicable. The warning signal lights shall be mounted at the front above the windshield and at the rear so that the lower edge of the lens is not lower than the top line of the side window openings. These lights must be capable of displaying to the front 2, and to the rear 2, overhead alternately flashing red lights.
Trans 300.54(1)(a)1m.
1m. On or after August 16, 2016, the following requirements shall apply to school buses:
Trans 300.54(1)(a)1m.a.
a. The school bus body shall be equipped with, in addition to the 4 red warning lights described in subd.
1., amber warning light shall be installed near each red warning light, at the same level, but closer to the vertical center line of the bus. The system of red and amber warning signal lights shall be wired so that the amber warning lights are activated manually, and the red warning lights are automatically activated, with the amber warning lights being automatically deactivated, when the stop signal arm is extended.
Trans 300.54(1)(a)1m.b.
b. An amber and a red flashing pilot light shall be installed in the driver's forward field of view indicating to the driver which warning light system is activated.
Trans 300.54(1)(a)1m.c.
c. The amber and red warning lights shall flash alternately at a rate of 60 to 120 cycles per minute. The “on" period shall be long enough to permit bulb filament to come to full brightness. A double flash effect shall be counted as a single flash.
Trans 300.54(1)(a)1m.d.
d. The above requirements in this subdiv. do not apply to school buses whose body was manufactured before January 1, 2005.
Trans 300.54(1)(a)2.
2. The amber and red warning lights shall be of seal beam construction or other approved type such as strobe or light emitting diode, not less than 5 inches in diameter or with a surface area of at least 19 square inches if not round and visible from a distance of at least 500 feet along the axis of the vehicle in bright sunlight.
Trans 300.54(1)(a)3.
3. There shall be a visible or audible means of giving clear and unmistakable indication to the driver when the signaling system is turned on.
Trans 300.54(1)(a)4.
4. Each amber and red warning light shall be mounted with its axis substantially parallel to the longitudinal axis of the bus.
Trans 300.54(1)(a)5.
5. The front and rear amber and red warning lights shall be spaced as far apart laterally as practicable, and in no case shall the spacing between lamp centers be less than 3 feet.
Trans 300.54(1)(a)6.
6. The front amber and red warning lights shall be located so that they can be clearly distinguished when headlamps are lighted on low beam.
Trans 300.54(1)(a)7.
7. The amber and red warning lights shall be mounted at the front above the windshield and at the rear so that the lower edge of the lens is not lower than the top line of the side window openings.
Trans 300.54(1)(a)8.
8. The front and the rear warning lights shall be unobstructed by any part of the bus from 5 degrees above to 10 degrees below horizontal and from 30 degrees to the right and 30 degrees to the left of the centerline of the bus.
Trans 300.54(1)(a)9.
9. The body immediately surrounding the area around the lens of each alternately flashing amber and red warning light shall have a black background extending outward a minimum of 3 inches. Where this is not practicable the background shall extend as wide as possible, with a minimum of a 1 inch black background required.
Trans 300.54(1)(a)10.
10. Amber and red warning signal ights may be equipped with hoods to shield from rays of sun for improved visibility.
Trans 300.54(1)(a)12.
12. Vehicles painted other than glossy yellow are prohibited from having the alternating amber and red flashing warning lights mounted on the vehicle except as otherwise provided by statute.
Trans 300.54(1)(am)
(am) Each school bus first registered on or after October 1, 1998, shall be equipped with a strobe light that conforms to the following requirements:
Trans 300.54(1)(am)1.
1. The strobe light shall be of solid state construction. It shall emit a white light by flashing, not rotating, 360 degrees around the vertical axis.
Trans 300.54(1)(am)2.
2. The strobe light shall be capable of operating continuously without any significant change in the flash rate under all operating conditions or weather extremes experienced in this state. The flash rate shall be no less than 60 nor more than 120 per minute. The double flash effect shall be counted as a single flash.
